Go
HTML has links - PDF has Authentication

Chapter 296-104 WAC

|Show DispositionsLast Update: 7/23/19

BOARD OF BOILER RULES—SUBSTANTIVE

WAC Sections

HTMLPDF296-104-001Administration—To what do these rules apply?
HTMLPDF296-104-010Administration—What are the definitions of terms used in this chapter?
HTMLPDF296-104-015Administration—When and where are the board meetings held?
HTMLPDF296-104-017Administration—How are rules affected if other rules are invalidated?
HTMLPDF296-104-018Administration—Interpretation of rules—Appeal rights—Hearings.
HTMLPDF296-104-019Administration—How are Washington state specials and extensions of inspection frequencies for boilers and pressure vessels obtained?
HTMLPDF296-104-020Administration—What are the filing requirements for boilers and unfired pressure vessels before their installation/reinstallation?
HTMLPDF296-104-021Administration—What is the registration requirement for new standard boilers and unfired pressure vessels?
HTMLPDF296-104-025Administration—What are the notification and reporting requirements following an accident involving a boiler or pressure vessel?
HTMLPDF296-104-030Administration—What is the penalty for operation of unsafe boilers or unfired pressure vessels?
HTMLPDF296-104-035Administration—What are conflicts of interest for inspectors?
HTMLPDF296-104-040Administration—When should inspectors submit inspection reports and on what forms?
HTMLPDF296-104-045Administration—What are the insurance companies' responsibilities?
HTMLPDF296-104-050Administration—What are the requirements for a boiler inspector?
HTMLPDF296-104-060Administration—When shall an inspectors' Washington state commission be issued, suspended, or revoked?
HTMLPDF296-104-065Administration—How should an inspector obtain a Washington state commission?
HTMLPDF296-104-100Inspection—How often must boilers and unfired pressure vessels be inspected?
HTMLPDF296-104-102Inspection—What are the standards for in-service inspection?
HTMLPDF296-104-105Inspection—How much time is required for notification of an internal inspection?
HTMLPDF296-104-110Inspection—What will be done when boilers or unfired pressure vessels are deemed unsafe or defective?
HTMLPDF296-104-115Inspection—What will be done when defective conditions are concealed by covering?
HTMLPDF296-104-125Inspection—What are the requirements for obtaining a certificate of inspection?
HTMLPDF296-104-130Inspection—When are inspection certificates valid?
HTMLPDF296-104-135Inspection—What are the requirements for restamping of boilers and unfired pressure vessels?
HTMLPDF296-104-140Inspection—How should a state number be assigned and applied?
HTMLPDF296-104-145Inspection—How are groups of vessels operating as a single unit classified?
HTMLPDF296-104-150Inspection—How are unfired steam boilers classified?
HTMLPDF296-104-151Inspection—What are the requirements for rental boilers?
HTMLPDF296-104-155Inspection—What preparations are necessary prior to internal inspections?
HTMLPDF296-104-160Inspection—What happens if a boiler or unfired pressure vessel is improperly prepared for inspection?
HTMLPDF296-104-165Inspection—When should coverings be removed for inspection?
HTMLPDF296-104-170Inspection—When are shop inspections required?
HTMLPDF296-104-180Inspection—How are radioactive systems inspected?
HTMLPDF296-104-200Construction—What are the standards for new construction?
HTMLPDF296-104-205Construction—What are the requirements for nonstandard new construction?
HTMLPDF296-104-210Construction—What are the requirements for construction of boilers and unfired pressure vessels of special design?
HTMLPDF296-104-215Construction—What are the requirements to use nonstandard boilers and unfired pressure vessels other than historical boilers and pressure vessels?
HTMLPDF296-104-220Construction—What are the requirements to use nonstandard second hand boilers and unfired pressure vessels, other than historical boilers and pressure vessels?
HTMLPDF296-104-226Construction—What are the requirements to use historical boilers and pressure vessels?
HTMLPDF296-104-245Construction—Combustible fluid heaters.
HTMLPDF296-104-251Installation—What are the standards for installation for nonnuclear boiler and pressure vessels?
HTMLPDF296-104-255Installation—What are the required clearances for boilers?
HTMLPDF296-104-260Installation—What are the required clearances for unfired pressure vessels?
HTMLPDF296-104-265Installation—What are the requirements for unfired pressure vessels installed underground?
HTMLPDF296-104-271Installation—How does an owner, user, or installer obtain a variance from clearances?
HTMLPDF296-104-273Installation—What inspections are required for reinstalled standard boilers or unfired pressure vessels?
HTMLPDF296-104-295Installation—What are the requirements for an explosion door?
HTMLPDF296-104-300Installation—What control and limit devices are required on automatically fired boilers prior to June 1989?
HTMLPDF296-104-301Installation—What control and limit devices are required on automatically fired boilers after June 1989?
HTMLPDF296-104-302Installation—What fuel controls are required on automatically fired boilers after December 1998?
HTMLPDF296-104-303Installation—What control and limit devices are required on automatically fired boilers after December 2004?
HTMLPDF296-104-307Installation—When are platforms around boilers required?
HTMLPDF296-104-316Installation—What safety pressure relief devices are required on boilers and unfired pressure vessels?
HTMLPDF296-104-320Installation—Where should the discharge from safety pressure relief devices, blow offs and drains be directed?
HTMLPDF296-104-325Installation—What are the requirements for boiler and unfired pressure vessel supports?
HTMLPDF296-104-405Existing installation—How can the maximum allowable working pressure be established for nonstandard boilers or unfired pressure vessels?
HTMLPDF296-104-502Repairs—What is the standard for nonnuclear repairs and alterations?
HTMLPDF296-104-503Repairs—What are the requirements for nonnuclear boilers and unfired pressure vessel repairs and alterations?
HTMLPDF296-104-510Repairs—When a lap seam crack is discovered along a riveted longitudinal joint on a boiler or unfired pressure vessel, what action is required and what repairs are allowed?
HTMLPDF296-104-515Repairs—Do riveted repairs to boilers and unfired pressure vessels require prior approval?
HTMLPDF296-104-520Repairs—What are the requirements for repair of nonnuclear safety devices?
HTMLPDF296-104-535Repairs—What are the requirements for nuclear repairs/replacement?
HTMLPDF296-104-540Repairs—What are the requirements for nuclear repairs of safety devices?
HTMLPDF296-104-700What are the inspection fees—Examination fees—Certificate fees—Expenses?
HTMLPDF296-104-701What are the civil penalties?
Site Contents
Selected content listed in alphabetical order under each group



Translate